Wood & steel frame
Wrought iron
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGate Repair Before & After in Sunrise Manor, NV
We could tell you we fix gates right. We’d rather show you. The photos below walk through the kinds of gate repair jobs we handle across Sunrise Manor, from sagging double gates in Winchester to operators that quit on a desert-hot afternoon in Whitney. Each one starts with a gate that won’t do its job and ends with one that swings, latches and closes on its own the way it should. Seeing the work speaks louder than any claim we could write.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Recent Transformations
These write-ups are representative of the gate repair work we take on in Sunrise Manor. Photo slots are ready and waiting, so the images can drop straight into the frame as each job gets shot. Every story below follows the same line: the problem, what the crew did about it, and the result the homeowner was left with.
Sagging Double Drive Gate: Hinge Post Rebuilt in Winchester
Before
AfterThe gate dragged on the ground every time it was opened and had scraped a groove into the pavers. A sagging gate sags at the hinge post, not in the middle, and the concrete around the post had cracked and let it lean. We reset the post, welded the hinge brackets back to true and hung the gate so it cleared the ground evenly. It swings square now and the homeowner stopped lifting it to close it.
Gate That Wouldn’t Stay Closed: Opener and Safety Sensors in Whitney
Before
AfterThe operator would start, then reverse halfway back every few seconds, leaving the gate open to the street. The magnet on the safety edge had gone bad and the control board read it as an obstruction. We replaced the sensor, tested the reversal distance and cleared the fault. The gate now runs the full travel and stops the way the code requires.
Rusted Sliding Gate Track: Panel and Track Welded On-Site in Sunrise Manor
Before
AfterA bottom rail had rusted through and the gate lurched sideways as it rolled. The homeowner expected a new gate; the panel was sound and only the rail was finished. We cut out the bad steel and welded in a fresh rail in the driveway, then trued the rollers. The gate rolls straight past the track edge it used to catch on. Fix the panel without the post and you’ll fix it twice, so we checked the posts before we called it done.
Operator Swap and Access Control: LiftMaster and Keypad in Winchester

An older opener kept tripping a breaker and the keypad had stopped accepting codes, so the family was leaving the gate open all day. We swapped in a LiftMaster operator, ran the control wiring properly and reprogrammed the keypad, then set the travel limits and tested the obstruction reversal. They have a working code at the keypad and a gate that closes on command again.
Cosmetic Reskin: Pickets and Welds in Sunrise Manor

Several pickets had bent and the paint was flaking off welds that had gone thin, so the gate looked worse than it was. We pulled the damaged pickets, welded in replacements and dressed the joints before they got a fresh coat. The gate matches the rest of the run and won’t leave sharp edges for a hand or a sleeve to catch on.
Gate Dragging and Off Its Post: Hinge and Roller Service in Whitney

This gate leaned into its post and took two hands to move, and the homeowner had started propping it open with a brick. We checked the post for movement, replaced the worn hinges and re-set the rollers, then adjusted the stops. It now clears the ground and closes on its own weight. Show me the gate closing on its own and I’ll show you where it’s failing; here the answer was the hardware, not the whole gate.
Safety First on Every Job
Gate springs, torsion components and operator arms under load can cause serious injury if they let go, and a powered gate that reverses incorrectly will close on a child or a car. We don’t hand out DIY steps for those parts. We service the operators and safety edges, test the reversal, and recommend a trained technician for anything under tension. Our crew is insured and bonded, and every repair carries the 90-Day Done Right Promise in writing.
Want Results Like These?
If your gate sags, drags, won’t latch or the operator keeps reversing, call (844) 761-8729 and a live person answers, day or night. We’ll look at it, quote a price up front and get it working. Repair over replacement where we can, and the 90-Day Done Right Promise on every job. Same-day help is often available across Sunrise Manor.
Written by the team at Gatewood Fence & Gate Sunrise Manor.
See the difference
Before
After
Before
After
Before
After