Wood & steel frame
Wrought iron
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Parts & Welding for Sunrise Manor Homeowners
A gate that drags on the ground, swings crooked, or won’t latch is usually a parts problem, and it’s the kind of problem we fix on site instead of talking you into a new gate. Gatewood Fence & Gate is locally owned and owner-operated, our technicians have up to 25 years of experience, and every job comes with the 90-Day Done Right Promise in writing. In Sunrise Manor we see the same thing over and over: steel gate frames that have taken twenty summers of desert sun and finally let go at the welds, hinge posts that have shifted in the caliche, and rollers that have ground themselves flat on driveways that settled years ago. We weld it, hang new hardware, and set it right in your driveway. Call (844) 761-8729 and a live person answers, any hour.

What Our Gate Parts & Welding Service Includes
Hinge Replacement
The hinge is where a gate gives up first, and a sagging gate almost always points at the hinge post, not the middle of the frame. When you need a hinge replaced, you’ll usually notice the gate dragging at the bottom or grinding as it swings, and no amount of oil quiets it for long. We cut the old hinge off, weld on a new one built for the weight of your gate, and check the post has not pulled loose in the process. If the post is moving, we tell you straight – hanging a new hinge on a loose post fixes it for a month.

Post Replacement
A hinge post that has rusted at the soil line or shifted in the ground takes the whole gate with it, and we’ve seen plenty of Sunrise Manor posts that have been patched and shimmed when they needed replacing. You need a new post when the gate no longer closes in the same plane it used to, or when you can rock the post by hand. We pull the old one, set the new one properly in concrete, and rehang the gate to it. It’s the kind of job that takes a half day and saves you three more repairs down the road.

Rail Repair
Rails carry the weight of the gate, so a cracked or bent rail means the gate is now working against itself every time it opens. We weld split rails, straighten bent ones where the steel is still sound, and replace the ones that have rusted through. Out here, rail repair usually comes down to rust that started inside the tube where you can’t see it, so we check the wall thickness before we start welding. If it’s too thin to weld safely, we say so and price a replacement rail instead.

Custom Welding
Custom welding covers everything that doesn’t fit a standard part: broken ornamental scrollwork, a gate frame that’s cracked at a corner, a latch mount that was never quite right, or a bracket you need made from scratch. We weld on site with the gate still hung, which means we can fit the repair to the gate as it actually sits, not as it sat on a bench. If your gate has a decorative element that broke, we’d rather repair the original than swap in a mismatched piece. That’s most of the reason people call us instead of buying a new gate.
Gate Rollers
Slider and cantilever gates lean on their rollers, and a roller that’s flat-spotted or seized makes the whole gate shove and jump on the track. You’ll hear it before you see it – a thunk or a grind at the same spot every time the gate moves. We replace rollers with units rated for the gate’s actual weight, check the track for the burrs that ate the old ones, and align the gate so the new set isn’t fighting the same problem. Worn rollers also load up the operator, so fixing them early saves the motor.
Latch & Lock
A latch that doesn’t catch is a security problem, not just a nuisance, and a lock that sticks in the summer heat is the same latch problem wearing a different hat. We repair or replace latches, self-closing hinges, and lock assemblies, and we check the gate closes square to the strike so the new hardware lines up without shimming. Sunrise Manor gates take a beating from grit and heat, so we set latches with a little tolerance rather than so tight they bind. Call us and we’ll look at it the same day.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Brands We Service for Gate Parts & Welding
We work on the gate hardware that shows up on most homes and small commercial properties in the valley. On LiftMaster operators we know the drive gears, limit switches, and the arm brackets that take the most load, so when a gate starts stalling or reversing we can trace it back to the mechanical side before anyone starts replacing electronics. With FAAC, we’ve handled plenty of the hydraulic arms and the pivot hardware they drive, which is usually where the wear shows up first. Linear and BFT systems are common on sliding gates here, and we know where those operators wear and which gate hardware has to be squared up to keep them running.
Whether you have LiftMaster, FAAC, Linear, BFT, or any other make, we can help. We’re familiar with the way these systems are built and the parts that fail under desert conditions, and we can tell you whether the gate itself needs repair or whether the operator is the real problem. If you’re not sure what you have, we’ll look at the labels and figure it out on site.
Signs You Need Gate Parts & Welding Right Now
- The gate drags, sags, or won’t close square. A gate that won’t close is a security gap, not just an inconvenience, and it usually means the hinge or the post has moved. Left alone, a dragging gate twists the frame and turns a small hinge job into a welding job.
- You can see rust coming through a weld or a joint. Rust at a weld line means moisture has gotten inside the steel, and the joint is losing strength from the inside out. Get it looked at before the crack opens up and the gate sags.
- The gate shudders or jumps on its track. A shudder on a sliding gate is a worn roller or a damaged track, and it puts extra load on the operator motor every cycle. Replacing a roller now is a lot cheaper than replacing an operator later.
- The latch won’t catch without a shove. That’s the gate out of alignment or the latch hardware worn past its tolerance, and it means the gate isn’t actually secure. A latch that catches on the third try will eventually stop catching at all.
- You’ve been told the whole gate needs replacing. Ask for the second opinion first. Many gates that get quoted for replacement only need hinge, post, or weld repair, and we’ll tell you honestly if the gate is past saving. Call for a free second opinion on any written estimate.
Our Gate Parts & Welding Process – Step by Step
- 1
We pick up the phone. A live person answers any hour, and we’ll ask enough questions to know whether it’s a hinge, a post, a roller, or a weld so we bring the right gear. No voicemail, no call queue three states away.
- 2
We look at the gate in place. We check the hinge post for movement, look for rust inside the rails, and watch the gate open and close to see where it binds. A gate tells you where it’s failing if you watch it move, so we do.
- 3
We give you the price before we start. You get an upfront price in writing, and we agree on it before any work begins. The number we quote is the number you pay, and there’s no trip charge inside the county.
- 4
We weld and fit on site. On-site welding means your gate stays in your driveway. We fit the repair to the gate as it hangs, check the alignment, and test every latch and roller before we call it done.
- 5
We stand behind it. Every job carries the 90-Day Done Right Promise in writing. If something we fixed isn’t right, one call brings us back, and we make it right, no runaround.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Parts & Welding Cost in Sunrise Manor?
A typical hinge replacement in Sunrise Manor runs $120 to $260 per hinge depending on the gate’s weight and whether the post needs attention too. Post replacement runs $350 to $800 because it means pulling, setting, and rehanging. Rail repair and custom welding usually land between $150 and $450 depending on how much steel is involved and whether the gate comes off its hinges. Roller replacement runs about $60 to $150 per gate, and latch and lock work runs $75 to $200. Steel gates and ornamental iron cost more to weld than aluminum, and rusted-out frames can push a repair toward replacement.

The way to avoid overpaying is to get a written, itemized price before anyone starts, and to ask for a free second opinion if you’ve been quoted for a full replacement. We’ll tell you which parts actually need work and which can wait. Our estimates are free and we’ll give you a price before we pick up a wrench. Take $40 off any repair over $200, there’s no trip charge inside the county, and seniors and veterans get a permanent 10% discount. Call (844) 761-8729 for a free estimate.
Gate Parts & Welding Near Sunrise Manor – Our Service Area
We serve Sunrise Manor and the surrounding towns, including Whitney, Winchester, North Las Vegas, Paradise, and Las Vegas. When your gate needs a repair we can handle, we’re close enough to look at it without a long lead time, and we can usually get out the same day for hinge, roller, latch, and small weld work. For custom fabrication we schedule it, and we’ll tell you exactly when. You can also see what we do on our Gate Parts & Welding in Whitney and Gate Parts & Welding in Winchester pages, or look at our home page to get a feel for the shop.
Serving Sunrise Manor, NV – Our Local Coverage Area
We serve Sunrise Manor and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Gate Parts & Welding in Sunrise Manor
It covers the hardware and structural repair side of a gate: hinges, posts, rails, rollers, latches, and custom welding. Instead of replacing the whole gate, we repair the part that failed and get the gate working again.
Most hinge, roller, and latch jobs take one to three hours. Post replacement is usually a half day, and rail repair or custom welding depends on the steel involved. We’ll give you a time window when we quote the job and show up in it.
Most repairs run $120 to $800 depending on whether it’s a hinge, a post, or a weld, and we quote the price in writing before any work starts. We’ll also check whether a free second opinion is worth getting if you’ve been quoted for a full replacement. Call (844) 761-8729 for an exact quote – estimates are free.
Yes. We service LiftMaster and other major gate brands, and we know where the mechanical parts wear out on each. If your gate is a brand we don’t handle, we’ll say so honestly rather than guess at the repair.
Yes for hinge, roller, latch, and small weld repairs when the schedule allows, and we answer the phone 24 hours a day. Call us and we’ll give you a realistic window and a price before we come out. If your gate isn’t latching or won’t close, call now.
Every job carries the 90-Day Done Right Promise in writing. If something we repaired isn’t right within 90 days, one call brings us back and we make it right at no charge.
Clear a few feet around the gate on both sides and make sure we can reach the gate’s power disconnect if it has an operator. If you have a prior written estimate, keep it handy so we can go over it. That’s it – we bring the rest.
Schedule Your Gate Parts & Welding Service in Sunrise Manor Today
When your gate is sagging, sticking, or not latching, call (844) 761-8729 and we’ll get it looked at. A live person answers 24 hours a day, the price is agreed before work starts, and every job carries the 90-Day Done Right Promise. Estimates are free, there’s no trip charge inside the county, and the Gate Parts & Welding in Sunrise Manor page is where it starts. Call now.
Written by the team at Gatewood Fence & Gate.