Wood & steel frame
Wrought iron
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Parts & Welding Across Whitney
If your gate has stopped latching, is dragging on a cracked roller, or the operator quit after the last heat wave, we can help. Our Gate Parts & Welding team works on gates across Whitney every week, and we know the 1980s and 1990s subdivisions here block by block, because that’s where the calls come from. We’ll tell you what’s actually wrong before anyone touches a welder, quote a written price, and get it done right. Call (844) 761-8729 and a live person picks up, day or night.
Why Gatewood Fence & Gate Sunrise Manor Is Whitney’s Preferred Gate Parts & Welding Company
We’ve built our name in Whitney the slow way: by showing up when we said we would and fixing what we found. Neighbors in the 89122 ZIP pass our number along because the person who answers the phone actually knows the trade and the person who shows up actually carries the tools. Every job carries the 90-Day Done Right Promise in writing, so if something we touched isn’t right, one call brings us back. Our technicians have up to 25 years of experience with everything from a builder-grade hinge that’s been baking since the Reagan years to a modern access keypad.
Whitney sits close to our Sunrise Manor base, so getting a truck out here isn’t a scheduling headache. That matters when a gate is stuck open on a 115°F afternoon and your yard is sitting exposed. We also hand out standing offers that don’t need haggling: $40 off any repair over $200, no trip charge inside the county, and a permanent 10% discount for seniors and veterans. Free second opinions on anyone else’s written estimate, too. Fix the panel without the post and you’ll fix it twice – that’s the thinking behind every job.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our Gate Parts & Welding Services in Whitney
Hinge Replacement in Whitney
A gate sags in the hinge post, not in the middle, and that’s where we start. In Whitney’s older subdivisions, original builder-grade hinges have carried the same gate for 25 to 35 years of desert heat, and the pins wear until the whole panel drops. We replace the hinge and check the post footing, because a new hinge on a loose post is money thrown at the ground. Typical hinge replacement in Whitney runs $150 to $360 depending on the number of hinges and whether the post needs help.

Post Replacement in Whitney
We’re not going to weld a gate to a post that’s already failing. Many of Whitney’s block-wall and wrought-iron setups have posts that were never footed properly for automation, so they lean and twist and the gate drags. We set a new post, tie it to the existing fence line where we can, and hang the gate true. Post replacement here usually lands between $400 and $1,200 based on the post type and how much digging the footing takes.

Rail Repair in Whitney
Rails take the worst of the windblown grit that kicks up off the open desert east of Whitney in the afternoons. That fine dust works into the joints and rollers and grinds the rail edges down, and eventually a drive-side rail cracks or warps. On-site welding lets us repair the rail in your driveway rather than hauling the gate away. Rail repair in Whitney typically costs $250 to $550 depending on the length and material.

Custom Welding in Whitney
Sometimes the right fix is a small weld, not a new gate. A cracked header, a broken picket, a bracket that pulled loose from a block wall – we bring the welder to the gate instead of hauling your steel off and leaving you waiting. Because Whitney’s older gates are often original iron with a history of repairs, we take extra care to match the existing profile and not build a patch that looks like a patch. Custom welding calls usually run $120 to $400 depending on how much has to be built up.
Trusted Brands We Service in Whitney
We service nine major gate brands and know their failure patterns well enough to diagnose fast. In Whitney, that includes older Linear operators common on builder-grade swing gates, Viking slide operators still running on driveways from the 1990s, Ghost Controls during retrofits, and DoorKing access control on any gated entry. We don’t stock parts on a truck, and we won’t pretend a specific part is already in a bin – what we do is identify the right replacement, order it, and get back out to fit it so the gate isn’t sitting half-apart for a week. If your brand isn’t on the list, call anyway; we’ll tell you straight whether we can help.
See the difference
Before
After
Before
After
Before
AfterCommon Gate Parts & Welding Problems We See in Whitney Homes
- Builder-grade operators that quit in the heat. The control boards and plastic gears on older LiftMaster and Linear units just can’t take Whitney’s 110°F-plus summers and relentless UV. When the controller drops, the gate usually needs more than a new board – we look at the whole system.
- Manual gates retrofitted with automation, no infrastructure behind it. A later-added operator on a 1989 gate often outpaces the original hinge post and footing, so the gate sags and the hinges get replaced again and again. We reinforce the post so the automation has something solid to push against.
- No conduit from the original build. Because most of these gates were installed manual, the power run was never planned. That leaves exposed wiring degrading in the heat, causing the operator and safety photocells to cut in and out. Sometimes we trench; sometimes a solar gate opener sidesteps the whole problem.
- Rollers and hinges seizing with grit, not rust. The dry valley doesn’t rust these parts the way a wet climate would, but the dust from the open desert east of Whitney packs in and jams them solid. Cracked plastic rollers and seized hinges are the most common call we get here.
Pricing for Gate Parts & Welding in Whitney, NV
Here’s what jobs actually run in Whitney’s market. Hinge replacement typically runs $150 to $360. Gate rollers run $90 to $220 depending on count and operator type. Rail repair is usually $250 to $550. Post replacement lands between $400 and $1,200, and custom welding calls run $120 to $400. If your operator also needs work, replacing a heat-failed control board or gear set generally adds $200 to $500 before labor. We quote every price up front and you approve it before anyone starts, so the invoice matches the number you agreed to. Estimates are free, and a second opinion on someone else’s written estimate costs nothing. Call (844) 761-8729 for an exact figure.
We Also Serve Cities Near Whitney
Whitney doesn’t sit in a vacuum, and neither do we. Homeowners reach us from Whitney and the surrounding east-side communities, including Sunrise Manor, Winchester, Paradise, and Las Vegas. If you’re just up the road from us, getting a truck out is easy. Same Promise, same live person on the phone, same written quote before work starts. Call and we’ll tell you when we can come.
Serving Whitney, NV – Our Local Coverage Area
We serve Whitney and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs – Gate Parts & Welding in Whitney
Heat-fatigued control boards or plastic gears are the usual culprit after a Whitney heat wave, especially on older builder-grade LiftMaster and Linear units. When you call, we’ll walk through the symptoms, then come out and check the post footing and hinge alignment, test the rack and pinion, and inspect the safety photocell. If the board or gears are gone, we replace them with modern equivalents that hold up better. Call (844) 761-8729 for a free estimate.
Yes, and we’ll tell you honestly what it takes. Many Whitney gates were installed manual back in the 1980s or 1990s, and adding an operator without reinforcing the post or addressing the lack of conduit usually means problems down the line. We check the posts, plan the power run, and either mount a reliable operator or recommend a solar gate opener to skip the trenching. It’s a measured, scheduled job, so call us and we’ll set up a free on-site estimate.
Because it’s grit, not rust. The wind kicks fine desert dust in from the open ground east of Whitney, and it packs into the rollers and hinges until they seize. In wetter climates you’d fight rust; here you fight abrasive dust and heat-fatigued plastic. We replace cracked rollers with heavy-duty ones, clear the tracks, and apply a dry lubricant that doesn’t collect grit. A roller swap typically runs $90 to $220. Call (844) 761-8729 to get it sorted.
Automatic gates in Whitney need functioning safety devices – at minimum a photo-eye or loop detector to stop or reverse the gate if something’s in the path. Because so many gates here were retrofitted from manual, these devices are often missing or degraded from sun and heat. We check for them on every automation call and fit what’s absent. Call (844) 761-8729 for a free walk-through and quote.
Sometimes, but not always, and that’s why we check the post footing first. A sagging gate in Whitney often means the hinge post itself is loose or was never properly footed, especially after being retrofitted with an operator. New hinges on a weak post will fail again in a year. We either weld and reinforce the existing post or set a new one – then the hinges hold. Call (844) 761-8729 for a free estimate before you buy parts.
If your Whitney gate is dragging, cracked, or just not doing what it should, the fastest thing you can do is call. We’ll tell you what it likely takes, quote the price in writing before anyone touches a tool, and back the work with the 90-Day Done Right Promise. Call (844) 761-8729 for a free estimate today.
Written by the team at Gatewood Fence & Gate Sunrise Manor.